A rack structure in which loading and unloading of the racks is accomplished by a stacker crane, or similar vehicle, without the aid of an on-board operator.
Code (enforced by the local building department) under which the structure is designed.
Typically, a horizontal structural member that has the primary function of resisting bending moments.
A pin, bolt, or other mechanism that resists disengagement of the beam connector from the column.
An essentially vertical truss system that provides resistance to lateral forces and provides stability for the structural system.
A rack structure comprised primarily of vertical columns, extended bases, horizontal arms projecting from the face of the columns, and down-aisle bracing between columns. There can be shelf beams between arms depending on the product being stored. Cantilever columns may be free-standing or overhead tied.
A specialized pallet rack structure in which either the horizontal shelf beams support case-flow lanes or case-flow shelf assemblies are supported by the upright frames. The case-flow lanes or shelves are installed at a slight pitch permitting multiple-depth case or box storage with loading from one service aisle and unloading or picking from another service aisle.
Exterior covering of structure.
Shape manufactured by press-braking blanks sheared from sheets, cut lengths of coils or plates, or by roll forming cold- or hot-rolled coils or sheets; both forming operations being performed at ambient room temperature; that is, without manifest addition of heat, such as would be required for hot forming.
One of the two principal directions of the storage rack, corresponding to the direction perpendicular to the principal handling equipment aisle. This is also referred to as the transverse direction.
Inclined structural member carrying primarily axial force in a braced frame.
When a shelf is loaded with loads stacked one on top of another in a pallet position.
One of the two principal directions of the storage rack, corresponding to the direction of the principal handling equipment aisle. This is also referred to as the longitudinal direction.
A rack structure comprised primarily of vertical upright frames, horizontal support arms, and horizontal load rails typically used for one-wide by multiple-depth storage. This structure includes an 'anchor section' with horizontal beams supporting the load rails. Loading and unloading within a bay must be done from the same aisle. A two-way drive-in rack is a special case where back-to-back rows of drive-in racks are combined into a single entity with a common rear post.
A rack structure comprised primarily of vertical upright frames, horizontal support arms, and horizontal load rails typically used for one-wide by multiple-depth storage. This structure lacks the 'anchor section' found in drive-in racks; therefore, loading and unloading from can be accomplished from both ends of a bay.
See Upright Frame
Members that are installed on an elevated rack supported platform or pick module walkway whose purpose is to provide fall protection for the occupants of the structure. Guardrails consist of a top rail, an intermediate rail and posts.
Smooth, continuous railing that runs up a stairway assembly to provide added balance and safety for the occupants as they walk up or down the stairway assembly.
A vertical plate (angle or barrier) that is installed at the edge of an elevated floor that is intended to prevent loose items from sliding off the edge of the floor.
A rack structure comprised primarily of vertical upright frames and horizontal shelf beams and typically used for one-deep pallet or hand-stack storage. Typically, the locations of a couple of shelf levels are 'fixed' with the location of the in-fill shelves being flexible.
Classification of structures based on the nature of their use.
Maximum horizontal distance from the centerline of the column at the floor to a plumb line that extends downward from the centerline of the column at the top shelf elevation divided by the vertical distance from the floor to the top shelf elevation.
Maximum horizontal distance (inches or mm) from the centerline at any point on the column to a plumb line from any other point on the column divided by the vertical distance (feet or m) between the two points.
The front and back shelf members that bear the weight of the load and transfer the load to the upright frames.
A specialized pallet rack structure in which the horizontal shelf beams support pallet-flow lanes. The pallet-flow lanes are typically installed on a slight pitch permitting multiple-depth pallet storage with loading from one service aisle and unloading from another service aisle.
Any load bearing member with the long axis on the horizontal plane and intended for use as support of unit loads in direct contact. (pallet and shelf supports and beams, not bracing).
A rack structure comprised primarily of vertical upright frames and horizontal shelf beams and typically used for one and two-deep pallet storage.
A member that extends between the shelf beams at a given level underneath the stored load that aids in the support of that load.
A rack structure comprised primarily of vertical frames and horizontal beams, typically having one or more platform levels of selective, case-flow, or pallet-flow bays feeding into a central pick aisle(s) [work platform(s)] supported by the rack structure.
Signage permanently and prominently displayed depicting the permissible loading of the rack.
An assembly, typically with four corner columns, that permits stacking of one assembly on top of another without applying any additional load to the product being stored on each assembly.
The weight of the item(s) placed on the rack.
A specialized pallet rack structure in which the horizontal shelf beams support push-back lanes comprised of tracks and carts. The push-back lanes are installed on a slight pitch permitting multiple-depth pallet storage. Loading and unloading are done from the same service aisle by pushing the pallets back.
A decked working surface supported by the rack structure.
A rack structure similar to other rack structures; however, this structure also includes wall girts and roof purlins or equivalent components used to support wall and roof cladding. This structure is designed to withstand wind and snow or rain loads in addition to the normal storage rack loads.
Maximum allowable product loading accounting for the design safety factors. The design safety factor includes such factors as load uncertainties, uncertainties in the analysis, material and geometric properties, fabrication and installation tolerances.
A surface that is provided in areas where order picking personnel may need to step off the normal walking area or pick module walkway to dislodge loads that may not have properly flowed to their correct position.
A classification assigned to a structure based on its Occupancy Category and the severity of the design earthquake ground motion at the site.
A classification assigned to a location based on the types of soils present.
See Portable Rack
A rack structure similar to one of the other rack structures that is serviced by an automated storage and retrieval machine.
An assemblage of load-carrying components that are joined together to provide interaction or interdependence.
Upright frames having two columns similar to the chords of a truss and diagonal and horizontal bracing attached to and located between the columns. The diagonals and horizontals become the web members of the truss. (It is referred to as a vertical truss.)
The total weight expected to be positioned in the rack consisting of the product load and pallet weight.
A structural assembly that transfers the vertical and horizontal loads to the floor. It is usually made up of two columns and bracing members between the columns. The beams of the rack are attached to the columns of the frames and transfer the loads to the columns.
A decking system used on pallet rack shelves. Wire decking is fabricated from welded wire mesh and generally has reinforcements in the form of channels or support wires. Its purpose is to provide additional support for stored material, as well as, becoming a safety net for unstable loads.
Copyright MHI © 2023 | All Rights Reserved
